1
Sale/Trade / Re: cleaning house
« on: January 30, 2017, 01:20:30 pm »
I'll take the 8 - sscv4 built, tested, never used in the show------10 each
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Lynx SSR4 / Re: Convert SSR4's to DMX
« on: January 16, 2017, 01:15:14 pm »
It appears that v2.0 boards do not support the new transformer in the BOM.
3
Lynx SSR4 / Re: Convert SSR4's to DMX
« on: January 11, 2017, 09:43:23 am »
I had that problem with the other SSR4's I have. It is almost easier to just set it in the firmware
4
Lynx SSR4 / Re: Convert SSR4's to DMX
« on: January 09, 2017, 06:04:59 pm »
The board is version 2
5
Lynx SSR4 / Convert SSR4's to DMX
« on: January 09, 2017, 12:13:01 pm »
I have a few SSR4's and want to add the DMX option.
Does the new BOM on Mouser work. I have concerns about the transformer and wanted to check before I order.
Does the new BOM on Mouser work. I have concerns about the transformer and wanted to check before I order.
6
xlights / xlights + EtD + my lack of understanding
« on: December 19, 2016, 04:07:22 pm »
Brand new at this PixelNet stuff and I'm not putting it together
Been trying to understand how to setup the network in xlights with my hardware. (EtherDongle, 16 port ActiveHub)
I'm a little confused the Wiki says the EtD does 4 universes at 4096 channels, but xlights only allows you to set 512 channels per universe.
How do you setup xlights to support 16,384 channels that the EtD can put out?
I tried but could only 512 channels from the DMX out on the ActiveHub and nothing out on the Pixlenet.
Been trying to understand how to setup the network in xlights with my hardware. (EtherDongle, 16 port ActiveHub)
I'm a little confused the Wiki says the EtD does 4 universes at 4096 channels, but xlights only allows you to set 512 channels per universe.
How do you setup xlights to support 16,384 channels that the EtD can put out?
I tried but could only 512 channels from the DMX out on the ActiveHub and nothing out on the Pixlenet.
7
Finished COOPS / Re: PixelNet Zeus Controller COOP
« on: May 26, 2015, 08:18:46 am »
qty 2 of kit #1
qty 2 of kit #2
qty 2 of kit #2
8
Finished COOPS / Re: Active/Passive/4Port HUB Coop
« on: April 14, 2015, 08:48:59 am »
I made a mistake in my initial post.
Please change it from (2) Kit#3 to (2) Kit#1
Please change it from (2) Kit#3 to (2) Kit#1
9
Finished COOPS / Re: SSC v4 2015 COOP ( Open for orders )
« on: April 07, 2015, 09:37:43 am »
Kit #1 20
Kit #2 20
Kit #3 20
Kit #2 20
Kit #3 20
11
Lynx Zeus / Re: Zues 16 possible replacement part on Mouser
« on: January 15, 2015, 11:08:34 am »
Demand is being evaluated currently.
Make sure you vote hereYou are not allowed to view links. Register or Login
Using previous history you might start to see them in the next few months, but I have found what I needed in the short term in the Buy/Sell/Trade forum, from some very helpful and pleasant members.
Make sure you vote hereYou are not allowed to view links. Register or Login
Using previous history you might start to see them in the next few months, but I have found what I needed in the short term in the Buy/Sell/Trade forum, from some very helpful and pleasant members.
12
Sale/Trade / WTB Smart String Hub/SSC (Purchased)
« on: January 14, 2015, 10:16:42 am »SSC's v3 so I can put on the test firmware, again Built/Kit/PCB.
Thanks for everyone's responses. I have met my needs.
Thank you, Brian
14
The Porch / Re: 2015 Coop Poll for Lynx Equipment
« on: January 07, 2015, 02:43:03 pm »
Would PCB only coop's be a good idea, once you hit the minimum for a run.
I would like to see the coop managers lives to be simpler, and sorting and sending this stuff out has got to be a real challenge to say the least.
I would like to see the coop managers lives to be simpler, and sorting and sending this stuff out has got to be a real challenge to say the least.
15
The Porch / Re: 2015 Coop Poll for Lynx Equipment
« on: January 07, 2015, 08:21:12 am »
I would like to second Steve's comment.
I like to save money with coops, but if the store had PCB's that would make me just as happy.
Machined cases might need a coop to work out though.
I like to save money with coops, but if the store had PCB's that would make me just as happy.
Machined cases might need a coop to work out though.