Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - kfxi

Pages: [1] 2 3 ... 8
1
Finished COOPS / Re: SSC v4 2015 COOP ( Open for orders )
« on: April 09, 2015, 10:20:33 am »


please add 5ea kit 1, 5ea kit 2, and 5ea kit 3 to my previous order


Ken Austin

2
Finished COOPS / Re: SSC v4 2015 COOP ( Open for orders )
« on: April 08, 2015, 10:48:31 am »


kit #1    10ea

kit #2     10ea

kit #3      10ea



Ken Austin



3
The Porch / TM 1804 IC MODULES
« on: November 13, 2014, 09:09:12 pm »
I purchased several TM1804 ic led pixel modules that I wanted to use to make a random  display.  I also purchased  some TH2010-X controllers to run them with,  I have tried to get them to come on but when I power them up nothing comes on other than a couple that glow dim, is the TH2010-X the controller I need to use?  I also have some LED2014-X controllers can they be used?  Any help or suggestions you can give will be greatly appreciated.


Ken

4
Sale/Trade / WTB
« on: October 06, 2014, 03:46:05 pm »
I need a BOB CAT DMX TESTER either built or unbuilt Please PM me if you have one for sale.


Ken

5
Finished COOPS / Re: Aether 2 COOP - OPEN FOR ORDERS
« on: September 08, 2014, 03:26:47 pm »
please put me down for 4 ea kit 1 and 4 ea for kit 4

6
The Porch / Re: VIXEN
« on: August 04, 2014, 10:27:56 am »
I have built the ETHER DONGLE but not programmed yet.  I have also  built 8 ZEUS 16 that I have not programmed yet.

Ken

7
The Porch / VIXEN
« on: August 03, 2014, 04:39:13 pm »
I am wanting to install VIXEN for my light show this year and I don't know whether to install VIXEN 3.0.6 or install VIXEN 3.0.10.  I am just getting started with PIXELS and I would like to use some of the NUTCRACKER mega tree sequences but I also want to keep my DMX stuff from last year.  I would appreciate any guidance you can give. I have used VIXEN 2.0 in the past so I have some working knowledge of VIXEN.  Thanks for your input.

Ken

8
The Porch / missing parts
« on: July 29, 2014, 10:33:31 am »
Started seperating parts to construct my last ZEUS 16 and found out that I am missing two parts.  Does anyone  have the Mouser part number for the LED and the part number for the MOSFET?  Thanks for your help

Ken

9
The Porch / Re: zeus part
« on: July 23, 2014, 10:17:47 am »
Thganks that is the part I needed

Ken

10
The Porch / zeus part
« on: July 22, 2014, 10:22:31 pm »
I was installing the 4 pin connectors where the computer plugs into the zeus board and I broke a pin, "dumb dumb dumb". Can someone give me the part number where I can order a replacement from mouser.

Thanks
Ken

11
The Porch / IC NEEDED
« on: July 15, 2014, 04:10:50 pm »
does anyone have a source for ST485BN  chips, I have tried all the major suppliers and they say it is no longer available.  There must be a replacement but I can't find one.

Ken

12
The Porch / POWER SUPPLY
« on: June 18, 2014, 12:23:07 pm »
I have a question,  I am building a ZEUS 16 and plan to use all sixteen channels with 128 pixels on each channel.  What power supply should I use.  Should I use a 12 volt power supply or is it better to use a computer supply?  What is the current draw for this type of configuration.  Where is the best place to get a deal on computer suplie?

Ken

13
Finished COOPS / Re: Zeus 8 and 16 Coop ** Open ** V2
« on: June 09, 2014, 05:03:18 pm »
please put me down for  4ea ZEUS 16 and 4ea ZEUS 8


Ken Austin

14
The Porch / Re: Plans for training 2014
« on: April 17, 2014, 10:14:18 am »
Is there going to be a show this year and if so when and where?

Ken

15
Vixen / Re: New Sequences using Vixen 3
« on: April 01, 2014, 04:14:44 pm »
That looks really good, I am currently using version one, where can I download the latest version

Ken

Pages: [1] 2 3 ... 8