Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - pete peters

Pages: [1] 2 3 ... 7
1
Lynx Aether / Aether 1 Troubles
« on: August 24, 2016, 12:34:57 am »
I have an Aether 1  that the red channel will go out and than if I HIT THE SIDE OF THE CASE IT WILL COME ON and function for awhile than go off again.  I also have no green channel at all.  What should I do to check this out?  Which one of the three clusters controls the green power?  I know I have signal output to my board because it worked before....  Any ideas why striking the case will turn the red channel back on?  NEED Some help!!

Thanks

Pete Peters

2
Sale/Trade / Re: WIRELESS EX/RX Ver. 2 Kits For Sale SOLD OUT
« on: October 04, 2015, 01:27:23 pm »
ALL KITS are SOLD


Thanks Much

Pete P

3
Lynx Wireless DMX / TX/RX Co Op Coming???
« on: September 29, 2015, 01:49:33 pm »
Does any one know if there will be TX/RX  Co Op soon???

I hope so!!


Thanks
Pete P

4
Sale/Trade / USB Dongles For Sale SOLD OUT
« on: September 21, 2015, 02:25:38 pm »
I have three  USB Dongles   New... Completely assembled...  Will program to be either DMX or PixelNet ... Your choice

$45   each  INCLUDES shipping and PayPal

If interested   Please send me a PM

Thanks

Pete P

5
Sale/Trade / Re: WIRELESS EX/RX Ver. 2 Kits For Sale
« on: September 21, 2015, 01:59:25 pm »
I have 13 kits avaialable

If interested  PM me

Thanks

Pete P

6
Sale/Trade / Re: WIRELESS EX/RX Ver. 2 Kits For Sale
« on: June 29, 2015, 11:13:42 pm »
  13  Kits   Remain

7
Sale/Trade / Lynx Express with Wireless FOR SALE------------SOLD OUT
« on: May 29, 2015, 05:26:35 pm »
Two  Version 5 Lynx Express  with Version 2  Wireless Mod 
 $70  each plus shipping and PayPal fee

Both have been tested in standard and wireless mode- Work Well
Both New- never been used in the field

Send me a PM if interested

8
Sale/Trade / WIRELESS EX/RX Ver. 2 Kits For Sale SOLD OUT
« on: May 25, 2015, 12:22:09 am »
13    Ex/Rx wireless KITS (not assembled) For Sale.

      The kits are all new and are Version 2  (see pic below for assembled view)

      $20 per kit plus Shipping  No PayPal fee

      If interested  send me a PM


      Thanks

      Pete P

9
Lynx Splitter / Re: DMX Splitter Output Problem
« on: March 29, 2015, 11:48:30 pm »
Thanks Very much to both of you!!

I installed the jumper as shown in the wiki.

Now ALL 4 Outputs work!!!

I will also look at upgrading the chips as well.

THANKS Again!

Pete P

10
Lynx Splitter / DMX Splitter Output Problem (Problem SOLVED)
« on: March 29, 2015, 01:29:12 pm »
Output four on my DMX Splittrer will not work.

Output 1, 2, 3  all work fine.

I have replaced the 485 chip,  Swapped it with other output chips,  I have  replaced the 8 pin socket. I have checked all the solder joints and re soldered the joints.  I have checked the boards foil traces and they check out OK.

I am stumped

Does anyone have any ideas??

Thanks  Much

Pete P

11
Lynx USB DMX Dongle / Re: Need Version 1 Hex File
« on: March 16, 2015, 04:00:46 pm »
You are not allowed to view links. Register or Login
Also, when you get the notification tone, what changes in the hardware listing?  Somewhere there is a USB device being added and you will need to see what it is.

The dongle was showing up as "other device - DLP USB245M" on the device manager list.  When I saw this I check to see if the driver was installed. I had windows install the driver and WA- LA  the dongle has an assigned Com Port  It works fine!

Feel kind of dumb for not realizing this sooner but THANKS to you I found the problem!

THANKS VERY MUCH for all your help!!!

Pete P

12
Lynx USB DMX Dongle / Re: Need Version 1 Hex File
« on: March 15, 2015, 11:36:55 pm »
You are not allowed to view links. Register or Login
What lights are lit on the dongle board?

This is Version 1  It has no lights

Thanks

Pete P

13
Lynx USB DMX Dongle / Re: Need Version 1 Hex File
« on: March 15, 2015, 10:29:45 pm »
You are not allowed to view links. Register or Login
Make sure that you have installed the FTDI drivers prior to plugging the USB dongle in.  If not, then Windows will install its driver which will not work.

The FTDI drivers are installed.  Check Sum is correct. Still not seeing it in the Com Port list..  My other dongle is working fine.  What else do I look at now?

Thanks
Pete P

14
Lynx USB DMX Dongle / Re: Need Version 1 Hex File
« on: March 15, 2015, 03:20:33 am »
Thanks Guys!

I have used the proper hex file and the proper check sum comes up when I program it with the PicKit 3

When I go to device manager in Windows, the notification tone goes off when I plug in the dongle, but the com port does not show up in the list.
I have another dongle and it gets the notification tone and it shows com port 7 on the list.
What should I check now?

Thanks

Pete P

15
Lynx USB DMX Dongle / Need Version 1 Hex File
« on: March 14, 2015, 06:52:31 pm »
I flashed my version 1 dongle with the Version 2 Hex file and now it will not work. I think I need the version 1 Hex but I can not locate it.

Anyone know where I might find it?

Thanks

Pete P

Pages: [1] 2 3 ... 7