1
Sale/Trade / Re: FS: SSC v4
« on: January 26, 2015, 10:40:31 am »
PM sent.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Lynx Express / Re: Lynx Express COOP?
« on: January 26, 2015, 07:59:13 am »"i scheduled mine by using Falcon Pi Player on a raspberry pi and it was faultless. i just exported from vixen to the pi system and away it went. couldnt have asked for better. i mean, everyone has their personal opinions on it all, try it all and see where you end up from there."
That's awesome!!
3
Lynx Express / Re: Lynx Express Newbie UK
« on: January 26, 2015, 07:55:19 am »
What and when is the first coop?
4
Sale/Trade / Found - Express Receiver
« on: December 27, 2014, 10:04:16 am »
Would love to buy one of these (EX/RX)Ver 2 assembled or not, board only or whole kit.
Thanks..
Found one thanks.
Thanks..
Found one thanks.
5
Lynx Conductor / Re: Conductor 'waiting'
« on: December 03, 2014, 09:21:14 am »
No but now i'm looking into using that or hardwiring the filter up.
6
Lynx Conductor / Re: Conductor 'waiting'
« on: December 02, 2014, 04:17:45 pm »
Just an fyi. My problem is related to the audio connection on the conductor. I haven't had a chance to look into it but I unplugged the fm xmitter and I have no problem starting/stopping a show. Thanks for all the advice.
8
Lynx Conductor / Re: Conductor 'waiting'
« on: December 01, 2014, 10:23:12 am »
ok i'll make sure I try multiple times..
thanks guys.
thanks guys.
9
Lynx Conductor / Re: Conductor 'waiting'
« on: December 01, 2014, 09:28:18 am »
Yeah I don't understand what's going on, it looks like it should just work. I'll try again with a single sequence and song and make a show out of that and see what happens.
Thanks for your help, I do appreciate it.
Thanks for your help, I do appreciate it.
10
Lynx Conductor / Re: Conductor 'waiting'
« on: December 01, 2014, 08:38:30 am »
I haven't tried to see if the schedule will play, I have just been trying to start a show manually by picking it, but nothing happens.
11
Lynx Conductor / Conductor 'waiting'
« on: December 01, 2014, 08:03:46 am »
Hey guys looking for some help please. I have a conductor flashed to v69 and am using version 3 of the ccp. I formatted the cf card, added some music files and sequences and created 2 shows. I put in a password and a schedule with a show and it appears that I can connect to the conductor. I can see the shows in the ccp and the conductor updates to the time on the pc. However when I attempt to play a show nothing is happening, the conductor just says 'waiting'. If i pull the card i see the card error. It looks like i'm communicating but the conductor won't start playing. Any suggestions? Thanks for your help.
12
Lynx EtherDongle / Re: Etherdongle conductor
« on: December 24, 2013, 08:01:24 am »
Ok thanks RJ. I'll get another one and swap it out. Have a great Christmas and New Year.
13
Lynx EtherDongle / Re: Etherdongle conductor
« on: December 23, 2013, 11:13:55 am »
Yeah I don't get it, I've never had a problem like this before. I was unplugging it to use the cat5 jumper cable to connect a usb dongle into the hub to program a smart string. I don't think I did but I could have confused the cables and plugged into an output on the active hub. I don't know, just trying to think what could have happened. I'm running my show with a laptop so I'm fine for this season.
14
Lynx EtherDongle / Etherdongle conductor
« on: December 21, 2013, 10:40:35 pm »
Hi guys. My etc/conductor has been running fine until I unplugged it from my router with the show running. Now I have no connectivity from either the router or direct to my laptop. The magjack flickers on plugging it in but then nothing. I reflashed he etd firmware, reflowed the magjack joints and still the same issue. Not sure what to try next. The laptops network jack blinks orange as i f it has slow connectivity, but nothing on the magjack. Any suggestions would be great. Thanks.
15
Lynx EtherDongle / Re: First addition of led nodes
« on: December 02, 2013, 11:17:56 am »
Thanks Keith!