Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - lizard050

Pages: [1] 2 3 ... 5
1
Sale/Trade / wtb etherdongle and zues 8
« on: November 14, 2019, 07:45:55 pm »
Im looking for 1 or 2 etherdongles and zues 8's.  I have sent out a couple of pm's to past for sale items but understand this site isn't frequented that often nowadays.   

2
Sale/Trade / Re: wanted - zues
« on: November 07, 2018, 01:31:35 pm »
bump.

3
Sale/Trade / Re: wanted - zues
« on: November 07, 2018, 01:30:48 pm »
Sent you a PM

4
Sale/Trade / wanted - zues
« on: October 26, 2018, 08:19:32 pm »
looking to pick up a zuess 8 or 2.  Maybe even a zues 16 if available.

Thank you
Brad

5
Sale/Trade / Re: doing some cleaning:) Zeus 8 and Zues 16 Assembled
« on: October 12, 2018, 04:29:01 pm »
Do you still have either of these?

6
Sale/Trade / Re: for sale Zues 8 pcbs and Zues 8 kits
« on: October 12, 2018, 04:28:16 pm »
Do you still have these?

7
Current Coop's / Re: ssc4/pigtails 2016 coop ( taking orders )
« on: June 13, 2016, 11:15:58 pm »
I'd like 12 kit 1, 12 of kit 2 and 12 of kit 3

8
Lynx EtherDongle / Re: Etherdongle/network issues
« on: November 17, 2015, 07:23:29 pm »
I'm restarting trying to trouble shoot these.   using the pick kit 3 with the MPLAB ipe program.  I tried reprogramming the 2 dongles. one was recognized and 1 was not.  As I just need to get 1 working I'll only be seeking help on that one at this time. 

It seems to program correctly.  If I do a "read" I get the checksum f8cd8eef back.

Assuming the etherdongle did program I then set it up in xlights.  I set up xlights using multicast e131.  starting universe 1, # of universes 32, one output is checked, channels set to 512. 

Etherdongle Green led is lit

When I run xlights in test mode I get the green magic jack light on and the yellow magic jack light will flash.  If I speed up the cycle speed in xlighs or use the rgb cycle tab with mixed color the yellow magic jack light will flash much faster.  Not sure if this means I am getting data from my lap top or not.

I am directly connecting my lap top to the etherdongle and I am not using a crossover cable.  I have tried many of the things discussed through the forum with no success.  Both etherdongles are from the January 2012 coop.  I believe this was the second etherdongle coop. 

I seem to be leaning to a set up issue vs hardware but am not 100% sure since 1 of the dongles will not even program maybe I messed this one up also.

Thanks for any help. 

9
Sale/Trade / wtb - usb pixelnet usb dongle
« on: November 16, 2015, 07:41:40 pm »
Looking for another dongle.  Assembled or kit. 

10
Finished COOPS / Re: Etherdongle COOP *** Open for Orders - Extended ***
« on: October 02, 2015, 10:10:56 pm »
Put me in for 1 Kit #1. 

11
Lynx EtherDongle / Help with etherdongle testing
« on: October 01, 2015, 06:56:42 pm »
I have 2 etherdogles I built last year.  I spent a lot of time trouble shooting them last year with a lot of help from people here.  I never got them to work and couldn't determine weather it was the dongles or my set up. The controller's I tested with were Zeus, hubs and express.  All would work with the usb dongle but not my EthernetDongles.  I am wondering if anyone would be willing to test them with their set up so I could verify the etherdongles actually work or don't work in order to have a better trouble shooting starting point.  I would obviously take care of the postage both ways. 

12
Finished COOPS / Re: PixelNet Zeus Controller COOP
« on: May 31, 2015, 02:45:38 pm »
Put me in for 1 kit #1, 2 kit #2 and 2 kit #4

13
Finished COOPS / Re: Active/Passive/4Port HUB Coop EXTENDED UNTIL 4/22!!!
« on: April 23, 2015, 04:39:11 pm »
Please put me in for 1 Kit#1 and 2 kit #5 and 2 kit #6.   

14
xlights / Re: xlights set up / software or hardware issue
« on: December 13, 2014, 03:34:08 pm »
always a relief when you get it figured out

15
xlights / xlights set up / software or hardware issue
« on: December 11, 2014, 11:33:35 pm »
I'm trying to get renard hardware, dmx (lynx) hardware and pixelnet 2 universes working together.  My set up is  3 usb outputs from pc.   1 to renard, 2 pixelnet dongles to combiner then to a an Active Hub.  From the active Hub I'm taking DMX out, pixelnet out to 12 sscs,  1 pixelnet out to 4 port passive hub and 1 to 2 zues'.  xlights is set up with renard channels 1st,  then 1 universe of pixelnet for my mega tree,  and a second pixelnet universe set up for the rest including the dmx channels.  Everything seems to test fine seperately.  However now putting it all togeter (2 dongle) if having problems.  I set both jumpers on the active hub to universe 2 and leave the dmx set on 1.  When this is set up this way everyhting on univerise 2 seems to randomly go on and off even with things turned off in xlights. 

Would the order set u in exlights of renard, pixelnet universes matter?

Should I be looking at the active hub ? 

Pages: [1] 2 3 ... 5