Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - royce

Pages: [1] 2 3 ... 5
1
Sale/Trade / Misc. parts for sale SOLD
« on: November 23, 2023, 01:44:57 pm »
 Make and offer for all or part. Send e-mail   You are not allowed to view links. Register or Login


   70 male and 90 female 2 wire pigtail Ray Wu  connector  good for power supply
   55 male and 190 female vampire plugs
   10 lynx express v5 controllers ( few need firmware added I'll give you the picket-3 if you take all)
    2  lynx smart string hubs
    2  lynx zeus 16 v1.1
    1  dongle
    1  pixelnet dongle
 

  All Sold

2
The Porch / Re: falcon with lynx how to ?
« on: October 08, 2020, 09:15:34 am »
I didn't use a cross over

3
The Porch / Re: falcon with lynx how to ?
« on: October 03, 2020, 09:10:40 am »
so do i need dongle between the lynx and v2 ?? or just a cable between them ?
thansk



I run a Ethernet cable from my falcon 3 to the the lynx controllers. I got 15 lynx, never had a problem. Everything on the lynx are led's only' pixels I use the falcom
 

4
The Porch / Re: falcon with lynx how to ?
« on: October 03, 2020, 09:02:31 am »
so do i need dongle between the lynx and v2 ?? or just a cable between them ?
thansk

5
The Porch / Re: Merry Christmas 2019
« on: December 25, 2019, 08:39:38 pm »
Merry Christmas and a happy New Year.

6
Lynx Express / Re: 1 channel don't light
« on: December 18, 2018, 06:58:36 pm »
You are not allowed to view links. Register or Login
You are not allowed to view links. Register or Login
  I have a LE -V5 controller. One channel stopped working. The led for that channel will light-up, but no power to the connector side.  I changed the chip. Before  I started changing parts, I would like some advice. Thanks

Hello!

What channel number is not working?

Changed the chip?   The optocoupler (the 6-pin IC) you swapped it with a known good one?

It's possible the TRIAC is bad, but I'd be eyeballing the soldering of the opto, resistor, the TRIAC solder joints, and finally, the terminal strip solder joints.  That's (by far) the number one problem of the Expresses I've repaired, bad or missing solder joints.  Especially ensure ALL of the solder joints of the opto are good.  Also, make absolutely sure the pins of the opto are all properly seated in the socket.   That's what I'd do before considering replacing the TRIAC as the majority of time, the TRIAC fails locked ON.

Please let us know!



Found my problem, I did all the re soldering still didn't work, so I did a ohm check  and seen I had a problem The left leg of triac goes to the + side of the channel connector and I didn't have any continuity there The middle leg goes to the fuse and the right leg goes to the 180 ohm Ended up taking the triac out and seen solder missing around holes in the board that connect to the circuits. Guess I got a dead #6. Had a  back up LE so life is good.

7
Lynx Express / Re: 1 channel don't light
« on: December 17, 2018, 09:34:16 pm »
Thanks for all the info. I'll let you know the results. It was channel 6 that stopped working.

8
Lynx Express / 1 channel don't light
« on: December 17, 2018, 03:01:48 pm »
  I have a LE -V5 controller. One channel stopped working. The led for that channel will light-up, but no power to the connector side.  I changed the chip. Before  I started changing parts, I would like some advice. Thanks

9
The Porch / Re: Pixels and just looking to vent a little :)
« on: December 21, 2016, 10:57:41 pm »
Sorry to hear about all your problems. I'm like you this year If it can go wrong it will. Hang in there it will turn around.

10
Nutcracker: RGB Effects Builder / text upside down
« on: December 07, 2015, 08:01:34 pm »
I'm using xlight/nutcracker 3.2.13 on my mega tree The Text is upside down. The letters are in the correct order their just upside down. Anyone else have this problem. Thanks

11
Finished COOPS / Re: SSC v4 2015 COOP ( Open for orders )
« on: April 09, 2015, 10:22:03 pm »


      I'd like  20 kit 3

12
Finished COOPS / Re: Lynx Express v5 Coop
« on: February 22, 2015, 06:15:28 pm »


     2 - kit #1 thanks

13
The Porch / Re: Everyone's recommended way to order from Ray Wu??
« on: February 09, 2015, 09:27:20 pm »
[

I have heard people say that customs charges have been received sometime after the shipment...  I've not see that.  My shipments come to me via DHL...  maybe they handle things differently than the other shippers? I'm interested in hearing how other people fair with customs and the different shipping companies.

[/quote]

I placed a order with Ray in December less than $300 and Dhl sent me a bill $17.47 for custom duty. I was surprised I got a bill.

14
The Porch / Re: Everyone's recommended way to order from Ray Wu??
« on: February 08, 2015, 06:08:03 pm »
I'VE CONTACTED RAY USING E-MAIL AND HAVE HAD GREAT  RESPONSE FROM HIM.

15
The Porch / It's over
« on: January 01, 2015, 06:10:14 pm »
 
  Last show was last night and today is demolition day.  I got 87% taken down and put away  and it drizzle all day. New Years day has always been the day when things come down, if only they would go up as fast. The show didn't go as planned but still a success. I got to start earlier this year but a said that last year. Anybody else start their tear down yet???

Pages: [1] 2 3 ... 5