Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - RickeyS

Pages: [1] 2 3
1
Sale/Trade / Smart string controllers
« on: February 12, 2017, 11:55:59 am »
10 started but not finished $12.00 plus shipping and PayPal fees, as show no extra parts

2
Sale/Trade / D.C. Controller
« on: February 12, 2017, 11:50:39 am »
$50.00 plus shipping and PayPal fees

3
Sale/Trade / 16 port hub
« on: February 12, 2017, 11:46:51 am »
$50.00 plus shipping and PayPal fees. Don't remember may need a couple fuses replaced

4
Sale/Trade / Wireless V2 (SOLD)
« on: February 12, 2017, 11:43:30 am »
$10.00 each plus shipping and PayPal fees

5
Sale/Trade / FS one Express V-5 (Sold)
« on: February 12, 2017, 11:38:18 am »
One version 5.0 $100.00 plus shipping and PayPal fees

6
Lynx Smart String / Re: SSC and LOR
« on: December 02, 2014, 08:04:13 pm »
Thanks all I kinda went in a different direction, I didn't want to buy new pixels, the ones I have has been on my roof for four years straight year around. I couldn't figure out to use LOR S3 software to control the pixels with RJs SSCs so I bought a tiny pix controller from holidaycoro and tried it with my pixels, low and behold works great. So I know not DIY but sure was easy and I like LOR S3 software. I have some of the first pixels from Ray, even though the outer tip has yellowed/darkened they look as good lit as the few I've had to replace. They are under the eaves so kinda of protected from the weather.

Again thanks
rick

7
Sale/Trade / Need Ether Dongle
« on: November 04, 2014, 07:19:43 am »
Anyone have a PCB or finished Ether Dongle willing to sell?

Thanks,
Rick

8
Lynx Smart String / Re: SSC and LOR
« on: November 03, 2014, 08:08:30 pm »
I guess I'm not understanding, I do have a hub. What I need to know is can LOR S3 output yo a Lynx usb dongle flashed with Pixelnet? I want to run S3 software to control my roof line which has 200 pixels controlled by the SSC controllers via a hub via a Lynx usb dongle. And then also control the pixlite controller via E.131

Thanks
Rick

9
Lynx Smart String / SSC and LOR
« on: November 03, 2014, 06:48:32 pm »
Is it possible to use a USB dongle flashed with Pixelnet with LOR? I want to control about 200 pixels along my roof line. At the same time I will be using E.131 to pixlite controller to control 12 WS2811 flex strips bought as a package from holidaycoro. I don't want to have to replace the pixels that are along my roof line (they have been up for three years)
Thanks
Rick

10
Lynx Smart String / Re: Couple of quick smart string questions regarding length and year-round use
« on: November 01, 2013, 06:21:52 am »
I've had nodes out year round for 3 years now (one of the first to get nodes from Ray) these are the orginal ones (no waterproofing) they are under the eve of my house (so no direct rain). I had to replace two nodes for Halloween this year (out of ~300). when looking at them upclose (not lit) you can see the plastic cover has yellowed some, but when lit them I can't tell the difference between the replaced nodes and the old nodes (replaced with nodes from the orginal order). I live in Delaware.

11
Lynx Express / Re: Repairs
« on: October 31, 2013, 11:54:41 am »
Also when replacing the triac's I find it easier to cut it off first with a small pair of wire cutters then heat up each leg one at a time and either push it out or small pliers and pull it out.

12
Bobcat DMX Servo Controller / Re: Can't program Pic?
« on: March 31, 2012, 04:33:29 pm »
Never Mind, I got it, my pic program was still 2.50 which didn't support PIC, updated to the newest firmware 2.61 and was able to program PIC

Rick

13
Bobcat DMX Servo Controller / Can't program Pic?
« on: March 31, 2012, 04:03:21 pm »
Hey everyone, I built my Bobcat servo controller but can't program the PIC, I thought maybe got a bad PIC but ordered two more PICs and still can't get them programed. I'm using a PICkit 2. I even tried to program them with the J1sys board with jumpers set to L and still says no device found. When I first start the software if finds the PICKit 2 but won't find the PIC18F23K20 to be able to program it. Any help would be appricated.
I have been able to program PICs for LE's, wireless etc. Just can't get this PIC programed. Must be doing something wrong. Please help
Thanks,
Rick

14
Finished COOPS / Re: DMX Tester and DMX Servo Controller COOP [CLOSED for orders]
« on: January 24, 2012, 06:29:20 am »
Got my Servo kit and spare PCB yesterday,

Thanks,

RickeyS

15
Finished COOPS / Re: 1st Express coop of 2012
« on: January 01, 2012, 08:05:55 am »
2 Please

Thanks
RickeyS

Pages: [1] 2 3