Difference between revisions of "Template:Set Address"
m (added program link) |
m |
||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
To program the Lynx Controller/Dimmer. | To program the Lynx Controller/Dimmer. | ||
| + | <br> | ||
| + | :<font color="red">Note: For MR16/DC Controller, where it says turn power on or off, substitute that for connect/remove the negative power lead to/from the MR16</font> | ||
| + | <br> | ||
| + | :<font color="red">'''Note2: Dongle DMX & Pixelnet Firmware - Require different software in order to set the start address'''</font> | ||
| + | :<font color="red">'''Note2: DMX Firmware you can use RJ's Lynx Address Program or DMX Deck'''</font> | ||
| + | :<font color="red">'''Note2: Pixelnet Firmware you can use Start Channel or xLights or your Sequence software with Pixelnet'''</font> | ||
| + | <br> | ||
| + | Step 1 - '''Turn off power to controller and move jumper to program mode''' <font color="red">'''Leave Power OFF until Step 3'''</font> | ||
| − | + | Step 2 - '''Use appropriate software (see Note2 above) and select address you need. Click on Program button''' | |
| − | + | ||
| − | Step 2 - ''' | + | |
Step 3 - '''Turn on controller and count to 5''' | Step 3 - '''Turn on controller and count to 5''' | ||
| − | Step 4 - '''Turn off controller and move jumper back to operation mode''' | + | Step 4 - '''Turn off controller and move jumper back to operation mode''' <font color="red">'''Leave Power OFF until Step 6'''</font> |
Step 5 - '''Click Stop on the Lynx Address Program''' | Step 5 - '''Click Stop on the Lynx Address Program''' | ||
| Line 13: | Line 19: | ||
Step 6 - '''Turn on controller and use your selected program to see if controller is now on the correct start address.''' | Step 6 - '''Turn on controller and use your selected program to see if controller is now on the correct start address.''' | ||
| − | '''Either exit | + | '''Either exit selected Program or go back to step 1 to program another controller''' |
| + | |||
| + | OPTIONAL Way if the above doesn't work - From RJ | ||
| + | |||
| + | Step 1 - '''Power up Controller.''' | ||
| + | |||
| + | Step 2 - '''Using selected program start to send the address you want.''' | ||
| + | |||
| + | Step 3 - '''With power ON carefully move the jumper to Program.''' | ||
| + | |||
| + | Step 4 - '''Count to 3 seconds.''' | ||
| + | |||
| + | Step 5 - '''Turn OFF the controller.''' | ||
| + | |||
| + | Step 6 - '''Put the jumper back to operate and power up controller to try/test.''' | ||
Latest revision as of 08:33, 1 March 2012
To program the Lynx Controller/Dimmer.
- Note: For MR16/DC Controller, where it says turn power on or off, substitute that for connect/remove the negative power lead to/from the MR16
- Note2: Dongle DMX & Pixelnet Firmware - Require different software in order to set the start address
- Note2: DMX Firmware you can use RJ's Lynx Address Program or DMX Deck
- Note2: Pixelnet Firmware you can use Start Channel or xLights or your Sequence software with Pixelnet
Step 1 - Turn off power to controller and move jumper to program mode Leave Power OFF until Step 3
Step 2 - Use appropriate software (see Note2 above) and select address you need. Click on Program button
Step 3 - Turn on controller and count to 5
Step 4 - Turn off controller and move jumper back to operation mode Leave Power OFF until Step 6
Step 5 - Click Stop on the Lynx Address Program
Step 6 - Turn on controller and use your selected program to see if controller is now on the correct start address.
Either exit selected Program or go back to step 1 to program another controller
OPTIONAL Way if the above doesn't work - From RJ
Step 1 - Power up Controller.
Step 2 - Using selected program start to send the address you want.
Step 3 - With power ON carefully move the jumper to Program.
Step 4 - Count to 3 seconds.
Step 5 - Turn OFF the controller.
Step 6 - Put the jumper back to operate and power up controller to try/test.
