1
Sale/Trade / Re: wtb dmx lynx usb dongle
« on: December 18, 2023, 03:19:25 am »
I will text my address in the morning.
Thank you very much and Merry Christmas!
Thank you very much and Merry Christmas!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Sale/Trade / wtb dmx lynx usb dongle
« on: December 15, 2023, 11:08:34 pm »
Looking for a dmx lynx usb dongle to reprogram my Aether.
Thanks!
Thanks!
3
Sale/Trade / Re: WTB USB DMX DONGLE
« on: October 23, 2019, 01:34:48 am »
Just logged in to say Hi! to RJ. Nice to see you post again.
4
Lynx Express / Re: Searching for Output Wire Sets for Lynx Express boxes
« on: June 05, 2016, 09:59:43 pm »5
The Porch / Re: 2014 display video
« on: December 26, 2014, 12:50:55 pm »
Amazing display! WOW!!! <res.
6
The Porch / Re: Have a favor to ask
« on: December 17, 2014, 10:55:47 am »
Don't have a fb account so I used my father's account and liked your display.
8
The Porch / Re: so far behind this year....if you have a sequence you can share...awesome!!
« on: December 09, 2014, 11:27:17 am »
Vixen? I have a few but mostly copied/downloaded and modified to suit my display. .. and they are not well polished. If it is vixen, I will post the video link here and if you like it, I can email you the file/s.
9
Vixen / Re: My 2013 sequences
« on: December 08, 2014, 12:47:49 am »
i did downloaded the profile also. i can see all the channels that's all.
10
Vixen / Re: My 2013 sequences
« on: December 04, 2014, 03:09:52 pm »
I downloaded the sequences but when I opened it all I see is blank sequences. What am I doing wrong?
11
The Porch / Re: Easy 27CH DMX512 dimmer Controller question
« on: October 29, 2014, 06:59:09 pm »
can I just connect it to an le via rj45, set the start channel and done? also, can I use a pc power supply to power it? how?
13
Lynx Aether / Re: What to do after accidentally plugging aether to 110v
« on: October 24, 2014, 12:47:23 am »
it seems that the replacement pic is also bad. after replacing the pic again, it started working properly. fixed two...one more to go.
14
Lynx Aether / Re: What to do after accidentally plugging aether to 110v
« on: October 23, 2014, 12:56:13 am »
I replaced LD33V but I am still getting 1.66 output and aether is not responding to a test sequence. Any suggestions?
15
Lynx Aether / Re: What to do after accidentally plugging aether to 110v
« on: October 23, 2014, 12:04:13 am »
I got one fixed... replaced blown fuse, burnt st485 and reflash and reprogram start channel of pic. Working okay now. one down two more to go.
I checked the reading of the second aether got the following:
LD33V
input=3.3 output=1.66 (BAD?)
7805
input=13.27 output=4.97 (OK?)
7812
input= 13.33 output=11.39 (OK?)
I replaced the fuse, st485 and pic already. All the response I got from the aether is a short burst of white when plugging it in. Not responding to test sequence. I will try to replace the ld33v and see if it fix it. Any other parts that I should check? Are the reading for 7805 and 7812 ok?
I checked the reading of the second aether got the following:
LD33V
input=3.3 output=1.66 (BAD?)
7805
input=13.27 output=4.97 (OK?)
7812
input= 13.33 output=11.39 (OK?)
I replaced the fuse, st485 and pic already. All the response I got from the aether is a short burst of white when plugging it in. Not responding to test sequence. I will try to replace the ld33v and see if it fix it. Any other parts that I should check? Are the reading for 7805 and 7812 ok?