1
The Porch / Re: hacking a spotlight to use with diy
« on: January 03, 2014, 01:43:34 pm »
can you post moer detail cant find anything online. i am curious also.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Lynx Smart String / Re: DSC programming
« on: October 17, 2013, 01:51:09 pm »
Thanks Jim it works . 
3
Lynx Smart String / Re: DSC programming
« on: October 16, 2013, 10:07:35 pm »
well I flash the dongle with the pixelnet, got it to program but its not responding with RJ dmx deck or vixen. I am done for tonight. Thanks for the help jnealand I got one step forward, I will try again tomorrow. good night.
4
Lynx Smart String / DSC programming
« on: October 16, 2013, 08:05:04 pm »
Hi can the DSC start address be programme with the dmx dongle. I have been trying for the last hour with Smart String Controller Configuration with no result its transmitting but don't seem to programme the start add. is there a FAQ on the SSC configuration software. here the settings on the Smart String Controller Configuration . start channel 1. usb dongle selected. 3 channel string. forward selected by default. node count 1. null mode 0 . string selected. click on transmit. now how long do you wait till it stops or do a manual stop. the DSC is set to program with 12 volt on. Please HELP.
5
The Porch / Re: What are these spot lights?
« on: July 25, 2012, 05:47:33 pm »
Hi Gator did you ever got you're ADJ cases put together with RGB LED and is it working good.
6
The Porch / Re: My RGB Star
« on: May 11, 2012, 02:40:06 pm »
exactly what i want to do with my star, its just beautyfull .
7
The Porch / Re: What are these spot lights?
« on: April 07, 2012, 08:55:51 pm »
Thanks Gator I will have to look at those case, right now the problem I have is to find a lens to focus the beam to about 6 to 20 degrees . I have these small lens that fits over the LED and its not working good at all.
9
The Porch / Re: addtional equipment for soldering
« on: March 30, 2012, 02:28:53 pm »
I do to make sure no bridges or miss pins and check parts numbers.
11
Bobcat DMX Servo Controller / Re: DMX sync issue?
« on: March 23, 2012, 10:00:04 am »
I have a similar issued, when I had an RGB LED connected it would flicker very faintly almost to the same pulse as the green dmx light on the board on the off sequence with vixen running. nothing serious great board just love it Dave.
Alain.
Alain.
12
Bobcat DMX Servo Controller / Re: How to controll RGB 350 MA LED
« on: March 22, 2012, 11:50:25 pm »
got it with a pnp like you said its reverse on is off in vixen . hey thanks for the help. like I said its been a while I used transistor, I guess its like riding a bike it come back after a few falls.
13
Bobcat DMX Servo Controller / Re: How to controll RGB 350 MA LED
« on: March 22, 2012, 11:43:41 pm »
I just check with a voltmeter and its a negative output on the bobcat dmx board so I need a PNP transistor in this case refresh my memory please its been a long time I did this type of electronics.
14
Bobcat DMX Servo Controller / Re: How to controll RGB 350 MA LED
« on: March 22, 2012, 11:33:29 pm »
thanks RM for the help. I just tried it and this time it remain off when connected with vixen running a sequence same as before but opposite result no blinky blinky.
15
Bobcat DMX Servo Controller / Re: How to controll RGB 350 MA LED
« on: March 22, 2012, 09:10:38 pm »
Well I tried this circuit and the LED come on and stay on with a vixen sequence running. when I disconnect it from the dmx servo board it goes off and when I touch the 500 kohm resistor to 6 volt power source it turns on and when I disconnect it goes off. then reconnect to the gate to the dmx board led output positive side it come on and stay on with a vixen sequence running. Connected a regular led 20Ma directly to the dmx board and it works like it should.
Here my circuit I am using can some body give me a little help Pleaase and Thank you.
Here my circuit I am using can some body give me a little help Pleaase and Thank you.